google.com, pub-1990720073119592, DIRECT, f08c47fec0942fa0 Samsung HLP2 Skip to main content

Samsung HLP2

















 Verify and make sure that  the ballast operation is OK before proceed.

The symptom can range from 



No video.

No turn On [Dead].

LED error code flashing.



There are 3 types of chassis involved in 2004 DLP line.  



L3 & L5 CHASSIS SET-UP


  1. Remove the lower back cover of the unit.

  2. Remove the Lamp Assembly from the Light Engine.

  3. Pull back the Light Engine Assembly slightly and do Ballast Test. Follow up.




  • Plug in the unit.

  • Turn Power ON.

  • During DLP lamp start process, the DMD PCB activates the Ballast
    PCB.  If the Ballast is operating properly, the linger Spark Gap Tube
    will begin to glow a few seconds into the process.  The Spark Gap Tube
    should only glow for a short time, and must go dark.  An audible sound
    is also heard during this time.  This procedure will repeat every 15 to
    30 seconds for approx: 2 to 4 minutes.  

  • If the Spark Gap Tune ignites, yet lamp never turns ON, make sure that the lamp is defective.

  • If the Tube does not light up; check and change the power supply
    PCB.  If it lights up, check/change the DMD PCB.  Check all connections
    from and to the DMD PCB.



L7 CHASSIS SETUP



  1. Remove the back cover of the unit.

  2. Remove Lamp Assembly from Light Engine.

  3. Remove plastic ballast cover and pull back the light engine.



L7 BALLAST TEST


  • Plug in the unit.

  • Turn power ON.

  • During DLP lamp starting process, the DMD PCB activates the
    Ballast PCB.  If the Ballast is operating properly, the Igniter Spark
    Gap Tube will begin to glow for a few seconds. The Spark Gap Tube will
    only glow for a short amount of time, and then go dark.  An audible
    sound is also heard during this time.  This process will repeat every 15
    to 35 seconds for a period of 2 to 6 minutes.  

  • If the Spark Gap Tube ignites, yet the Lamp never turns ON, replace the Lamp.  It is defective.

  • If the tube does not light up, check and change the power supply
    PCB.  If it lights up, check/change the DMD PCB.  Check all connections
    to and from the DMD PCB.



Comments

Post a Comment

Popular posts from this blog

Firmware TP.SK516S.PC821

  TP.SK516S.PC21 Firmware Download Available  Imran Ashraf Whatsapp Support QR Code  It's looks like you're searching for firmware or software related to the TP.SK516S.PB802 Mother Board Find the Correct Firmware on my this website  1. Check Your TV Brand & Model    - The TP.SK516S.PC821 is Main Board Number      2. Correct Resolution It's FHD or UHD 3. Get From Trusted Website and Trusted Person Like Imran Ashraf 10 Years in this     - If the firmware isn’t available on this website you may need to contected Imran Ashraf he can arrange your requirements       4. Caution with Firmware Flashing      Never download firmware from untrusted sites —it may contain malware or brick your TV.      - Ensure the firmware **exactly matches** your TV model and hardware version. If You Need Further Help: - Contact Whatsapp Support+923139292880 - Specify the issue (e.g., boot loop, no...
Post a Comment
Read more

Philips Codes

PHILIPS - 32PF 5320/28 (Service Mode, Error Codes & Fault Finding] Cont:- Philips 32PF 5320  Service Mode, Error Codes & Fault Finding [Cont:] NO PICTURE, BLANK SCREEN WITH CORRECT SOUND OUTPUT. Check whether the user menu is visible. If the user menu is OK, activate teletext mode. If teletext is OK, the problem is in the ADC [B18]&[Columbus 3D combfilter [B19], if present [depending on model]. If the user menu is not visible, check the LCD panel back light is ON. If the back light is OFF, the problem is in the power supply board or LCD panel.  Also check pin 12 (Lamp_ON_OFF) of 1J02.  It should be high, during normal operation. Fault finding purposes, it is important know the following:-   In Pixels Plus and Digital Crystal Clear models, which have an ADC [Analogue to Digital Converter] (B18), and Columbus 3D comb filter (B19), the digital input of the scaler is used for digital video path (Hercules output), whereas the analogue RGB output , a...
Post a Comment
Read more

Philips Com

PHILIPS - 32PF 5320 [LCD PANEL REMOVAL] DISASSEMBLE PROCEDURE DISASSEMBLY Cautiously pull back the upper part of the anti-static copper foils next to left and right speakers. do this in such a way that the foils are no longer attached to the metal ground plate on which the SSB board is mounted. Disconnect cables  form the "L" and "R" speakers. Unplug the LVDS connector  on the LCD panel. Be careful. This is a very fragile connector.  Unplug connections of the side I/O panel, the Top Control Panel, and the LCD panel on the SSB board Unplug 520 & X530 connectors on the power supply board. Instead of X520 also connector 66B on the other end of flat cable can be unplugged.  Lift the metal frame, together with all PCBs from the LCD panel.  Take care not to damage fragile LVDS cable, the 66B connector, and the anti-static copper foils.  Take care of these too, when later re-assembling the TV set, and replacing the copper foil. After removal of the...
Post a Comment
Read more