google.com, pub-1990720073119592, DIRECT, f08c47fec0942fa0 Hitachi LCD Repair Skip to main content

Hitachi LCD Repair



Hitachi LCD Repair Tips







15LD2200 -No-Fuse F1 pictures and C16 or C5 (150N) on the inverter board

-No picture-check fuse F1 and C16 or C5 (15 on) on the inverter board

22LD4200 -Lost picture after diferent time-Dry joints IC100 on board video processor (17MB10).

-Figure disappear after a while-check the connection on the video processor on board IC 100

22LD4200- No pictures sound ok, no pictures after diferent time on 17amp07 CHECK 5v p / s board if less 3.0 or 1.5 replaced C111 (25v1000mkgf)

-There is no sound good picture, no picture after a while check TEG 5v on board 17amp07 p / s if less dar ata 1.5v 3v switch c11 (1000mkgf 25v)

22LD4200 -Lines on the picture Bad conection between PS (PL108) and the video board (PL100).

-The line in the figure because of a bad connection between the PS (PL108) and Board video (PL100)

22LD4200 -line-Green Flashing green horizontal line across the screen intermittently flashing-Remove resistor R149 on the input signal board and replace it with jumper SMD (0 W)

22LD4200 -St-by redlight go green and back to red-transistor (Q104 BC548) and Resistor (100oM).

22LD4500U- No sound- Very low sound on terrestrial and no sound on digital inputs or any AV-memory Replace IC302 Type 24LC16.All customer controls are set to minimum on the new IC. Please reset the language and all the picture controls to normal after replacing the IC.

26LD6200 -Lines on the screen, strange picture-Replaced cable from the main board to the screen.

26LD6200/32LD6200 -No pictures or lost after 10.20 sec-replaced the inverter board (P.Suplly) 17PW11-2 (24Volts)

26LD6200/32LD6200 - The unit does not work, standby LED not lighting-Replace L500 and L501 Ferrite bead with a jumper wire.

26LD6600/32LD6600 - Looks like no-fault Synchro impulse eeprom Just go in service menu (menu, 4,7,2,5)-Factory reset option.

26LD6600/32LD6600 - no sound-Reinstate sound settings as follows:
Enter Service mode.Press menu then 4,7,2,5.
Go to Audio menu.
Select Sound 2. and enter the following values:
FM Prescaler 15
NICAM prescale AVL ON 35
SCART prescale AVL ON 14
SCART VOLUME 122 AVL ON
STANDBY TO GO TO SETTINGS Memorise
Reinstate sound settings as follows.

26LD6600/32LD6600 - Lines on the screen-Cable from the main board to the screen super glue it.

26LD6600/32LD6600 -Lines, pictures no back light present-resoldered IC224 (videoprocesor).

26LD6600/32LD6600 -

28LD5200- No color Colour drops out after the unit has been running for two to three hours.Resolder capacitor C510 and other components in its vicinity.

32LD9700 -No sound bad conection in PFA1 (HDMI board) pin 2 press just take it out and put it back.

32LD9700/42LD9700 -No sound bad soldering on cristal X800 (HDMI board).


Comments

Post a Comment

Popular posts from this blog

Firmware TP.SK516S.PC821

  TP.SK516S.PC21 Firmware Download Available  Imran Ashraf Whatsapp Support QR Code  It's looks like you're searching for firmware or software related to the TP.SK516S.PB802 Mother Board Find the Correct Firmware on my this website  1. Check Your TV Brand & Model    - The TP.SK516S.PC821 is Main Board Number      2. Correct Resolution It's FHD or UHD 3. Get From Trusted Website and Trusted Person Like Imran Ashraf 10 Years in this     - If the firmware isn’t available on this website you may need to contected Imran Ashraf he can arrange your requirements       4. Caution with Firmware Flashing      Never download firmware from untrusted sites —it may contain malware or brick your TV.      - Ensure the firmware **exactly matches** your TV model and hardware version. If You Need Further Help: - Contact Whatsapp Support+923139292880 - Specify the issue (e.g., boot loop, no...
Post a Comment
Read more

Philips Codes

PHILIPS - 32PF 5320/28 (Service Mode, Error Codes & Fault Finding] Cont:- Philips 32PF 5320  Service Mode, Error Codes & Fault Finding [Cont:] NO PICTURE, BLANK SCREEN WITH CORRECT SOUND OUTPUT. Check whether the user menu is visible. If the user menu is OK, activate teletext mode. If teletext is OK, the problem is in the ADC [B18]&[Columbus 3D combfilter [B19], if present [depending on model]. If the user menu is not visible, check the LCD panel back light is ON. If the back light is OFF, the problem is in the power supply board or LCD panel.  Also check pin 12 (Lamp_ON_OFF) of 1J02.  It should be high, during normal operation. Fault finding purposes, it is important know the following:-   In Pixels Plus and Digital Crystal Clear models, which have an ADC [Analogue to Digital Converter] (B18), and Columbus 3D comb filter (B19), the digital input of the scaler is used for digital video path (Hercules output), whereas the analogue RGB output , a...
Post a Comment
Read more

Philips Com

PHILIPS - 32PF 5320 [LCD PANEL REMOVAL] DISASSEMBLE PROCEDURE DISASSEMBLY Cautiously pull back the upper part of the anti-static copper foils next to left and right speakers. do this in such a way that the foils are no longer attached to the metal ground plate on which the SSB board is mounted. Disconnect cables  form the "L" and "R" speakers. Unplug the LVDS connector  on the LCD panel. Be careful. This is a very fragile connector.  Unplug connections of the side I/O panel, the Top Control Panel, and the LCD panel on the SSB board Unplug 520 & X530 connectors on the power supply board. Instead of X520 also connector 66B on the other end of flat cable can be unplugged.  Lift the metal frame, together with all PCBs from the LCD panel.  Take care not to damage fragile LVDS cable, the 66B connector, and the anti-static copper foils.  Take care of these too, when later re-assembling the TV set, and replacing the copper foil. After removal of the...
Post a Comment
Read more